How to adjust the small elevator of household villa to static balance?

開始之前一定要保證家庭別墅的小電梯轎廂沒有扭曲。確保不變形的時間是汽車組裝時。如果汽車變形，下一次的靜平衡就不可能了。因此，當家用別墅小型電梯平衡和滾輪導靴調整開始時，汽車的龍門框架需要是自由的，沒有變形。如果失真確實存在，則需要在啟動前進行調整。

Before starting, make sure that the small elevator car of the family villa is not distorted. The time to ensure no deformation is when the car is assembled. If the car deforms, the next static balance is impossible. Therefore, when the balance and roller guide shoe adjustment of the small elevator in the home villa begin, the gantry frame of the car needs to be free without deformation. If distortion does exist, it needs to be adjusted before starting.

工作順序：

Working sequence:

1、家用別墅進行小型控制電梯開到。

1. Small control is carried out in the family villa, and the elevator is driven to the top floor.

2、對準滾動導靴，使導軌定位在導靴座的中，導靴的推力構件定位。

2. Align the rolling guide shoe so that the guide rail is positioned in the of the guide shoe seat, and the thrust member of the guide shoe is positioned.

3、將牽引輪中間鋼絲繩的引線一直懸掛在客車頭盤上。如果鋼絲繩是偶數，就把它掛在相鄰兩根鋼絲繩的中間。如果是單數的，把它掛在中間的鋼絲繩的前面或后面，但是你需要保持距離。同時要保證鉛錘與車頂繩頭板的距離。因為車頂繩頭板上的孔一般是兩排，所以應該有足夠的空間懸掛鉛錘。

3. Hang the lead wire of the steel wire rope in the middle of the traction wheel on the head plate of the bus all the time. If the wire rope is even, hang it between two adjacent wire ropes. If it is singular, hang it in front of or behind the middle wire rope, but you need to keep a distance. At the same time, ensure the distance between the plumb and the roof rope head plate. Because the holes on the roof rope head plate are generally two rows, there should be enough space to hang the plumb.

家用別墅小型電梯

Small elevator for household Villa

4、接下去就是主要通過講述自己如何進行移動轎頂繩頭板。我們已經不能沒有太強調移動轎頂繩頭板僅是讓轎頂繩頭板的中目標對準曳引輪的中。移動繩頭板的目的發展不是現在想來實現平衡在某一具體位置的轎箱。如果轎頂繩頭板為可移動式，則可使用移動繩頭板對準曳引輪。如果轎頂繩頭板為固定式且用螺栓固定在橫梁上，可拆去原螺栓，螺栓可以暫時無法可用1/2”加墊片來代替3/5”，沿著一個立柱的方向以及移動。

4. The next step is to talk about how to move the rope head plate on the car roof. We can't emphasize too much that moving the car roof rope head plate is only to align the middle target of the car roof rope head plate with the middle target of the traction wheel. The purpose of moving the rope head plate is not to balance the car at a specific position. If the car roof rope head plate is movable, the movable rope head plate can be used to align the traction wheel. If the car roof rope head plate is fixed and fixed on the beam with bolts, the original bolts can be removed, and the bolts can not be used temporarily. 1 / 2 "and gasket can be used to replace 3 / 5" and move along the direction and direction of a column.

注意學生這時在移動繩頭板時需要具有十分需要小心，因如螺栓掉出就會直接導致轎箱墜落。這時用4個“C”型夾夾住繩頭板和上梁，使得繩頭板不會發生前后移動，繩頭板可以用撬棒沿著設計立柱工作方向不斷移動，記住這些完成后企業需要更換回3/5“的螺栓。這時他們可能需要在橫梁上開槽，開槽前需要用科學定位銷定好位，然后鉆一新孔，不要因為在前后方向研究移動繩頭板。

Note that students need to be very careful when moving the rope head plate, because if the bolt falls out, the car will fall directly. At this time, four "C" clamps are used to clamp the rope head plate and the upper beam, so that the rope head plate will not move back and forth. The rope head plate can move continuously along the working direction of the designed column with a crowbar. Remember that after these are completed, the enterprise needs to replace the 3 / 5 "bolts. At this time, they may need to slot on the cross beam. Before slotting, they need to fix the position with a scientific positioning pin, and then drill a new hole. Do not move the rope head plate because of studying in the front and rear direction.

以上就是為大家介紹的有關別墅家用電梯的詳細介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務

The above is a detailed introduction to the villa household elevator. I hope it will help you If you have any questions, please contact us We will provide you with professional service